Stadium capacity calculator
A football stadium's capacity is the number of rows you can fit along each side of the pitch times the seats in each row, plus any filled corners. Set the rows, tiers, corners and run-off below and the calculator counts every seat the way Stadium Designer's editor does. As a guide, a two-tier bowl with 48 rows a side and filled corners holds 42,822.
Capacity of the starter grounds
Counted seat by seat by the same engine the calculator uses.
| Ground | Stands (tiers / rows) | Capacity |
|---|---|---|
| Harbour Park | 2/42 · 1/26 · 1/30 · 2/34 | 25,087 |
| Elmfield Road | 2/30 · 1/18 · 1/16 · 1/14 | 14,688 |
| The Kiln | 1/28 · 1/34 · 1/30 · 1/24 | 23,881 |
| The Meridian | 2/48 · 2/48 · 2/48 · 2/48 | 42,822 |
| Ottermill Rec | 1/8 · 1/5 · 1/4 · 1/4 | 4,044 |
Rules of thumb for a design game, not engineering or safety advice.
Stands, roofs, corners, boxes and seat mosaics in 2D and 3D, then run a matchday or a concert and share the poster. Free, in your browser.
How it works
The calculator builds a real stadium from your inputs and counts it with Stadium Designer's engine, so the number is the one you'd see in the editor for the same ground. The pitch is 105 × 68 m. Run-off is the strip between the touchline and the front row; the stands sit behind it.
- Rows along a side. Every row runs the full length of its side. A seat takes 0.5 m of the row, with radial aisles cut through at regular intervals.
- Row depth. Each row is 0.8 m deep, so a tier of 30 rows is 24.0 m from front to back. Up to three tiers, each of 4 to 40 rows, stack behind and above each other.
- Corners. A filled corner is a quarter ring between two stands. If both neighbours are the same shape it takes their full section; otherwise it follows the lower tier of the shallower one.
- Run-off. More run-off makes every row slightly longer but pushes every seat further from the action. Tight grounds feel louder.
Worked example
Harbour Park, the default ground in the editor, has a single-tier Quayside Stand of 26 rows: 5,564 seats, about 214 per row. Add a two-tier main stand, two ends and two filled corners and the whole ground comes to 25,087.
Capacity is only half the job. Bigger grounds cost more, take longer to empty and need steeper back rows to keep the view: try the stadium cost calculator and the sightline calculator.
Frequently asked questions
How do you calculate a stadium's capacity?
Count the seats in one row along each side of the pitch, multiply by the number of rows, and add the corners. In Stadium Designer a seat takes 0.5 m along the row and a row is 0.8 m deep, with gaps left for radial aisles, so a long side of 48 rows holds about 10,368 seats.
How many seats fit in one row along a football pitch?
Along a long side of a 105 × 68 m pitch with run-off, about 216 seats per row once aisles are taken out; behind each goal about 148. In a straight stand every row holds the same number; only corner rows get longer as they go back.
How much capacity do filled corners add?
A lot. The Meridian preset gets 7,878 of its 42,822 seats from its four filled corners, about 18% of the ground. Corner rows get longer the further back they are, because each one is a bigger quarter circle.
How many rows does a 40,000-seat stadium need?
With seated corners, roughly 48 rows a side in two tiers: The Meridian preset's 2 tiers of 48 rows in total give 42,822. Without corners you'd need more rows, and the back rows end up a long way from the pitch.
Is this the same as a stadium's licensed capacity?
No. This counts the places you've built. A real ground's safety certificate sets its licensed capacity, which can be lower once exits, stewarding and sightlines are taken into account. Treat the result as a design figure for the game.
Rules of thumb for a design game, not engineering or safety advice. The calculators use Stadium Designer's simplified model; real grounds are designed by qualified engineers to the Guide to Safety at Sports Grounds and local licensing conditions.