StadiumDesigner
Guide

Stadium sightlines and the C-value, explained

By MakeHelm Ltd · Updated

A stadium's sightlines are measured with the C-value: how many millimetres your line of sight to the pitch passes above the eyes of the person in front. UK guidance recommends 90 to 120 mm for new seating, and the need to hold that number row after row is why stands get steeper towards the back.

The C-value decides whether you watch the match or the back of someone's head. It also sets the shape of the whole stand, which is why stadium architects work it out before almost anything else.

What the C-value measures

Pick a point on the pitch that every spectator should be able to see. For football it is usually the near touchline, since anything further away is easier to see over the crowd. Draw a line from a spectator's eye to that point. The C-value is how far that line passes above the eye of the person sitting directly in front.

The standard formula, the calculation drawn in the Green Guide, is:

C = D (N + R) / (D + T) − R

  • D: horizontal distance from the eye of the spectator in front to the point of focus
  • N: riser height, the step up from one row to the next
  • R: height of that spectator's eye above the point of focus
  • T: tread depth, the front-to-back depth of a row

Small changes in the riser make a big difference. Take a row 30 m back from the touchline, with eyes 10 m above it and 800 mm rows. A 400 mm riser gives a C-value of about 130 mm. Cut it to 350 mm and C drops to about 81 mm, below the recommended range. Fifty millimetres of concrete per row is the difference between a good seat and a poor one.

What 60, 90 and 120 mm feel like

The three numbers you will see quoted most often are 60, 90 and 120 mm. The Wikipedia summary of the FIFA standard calls them the absolute minimum, the recommended minimum and the optimum.

  • 120 mm: your line of sight clears the head in front, even with a hat on or when they lean forward a little.
  • 90 mm: you see over most heads, helped by seats in alternate rows being slightly offset, but a tall person in front means tilting your head now and then.
  • 60 mm: you are looking between heads rather than over them, and you will lose the near touchline whenever the row in front shifts.

The Sports Grounds Safety Authority, which publishes the UK's Guide to Safety at Sports Grounds (the "Green Guide"), recommends 90 to 120 mm. Its guidance on safe standing says designers who propose anything below 90 mm must show that spectators' views will not be compromised.

Why rows get steeper going back

Rearrange the formula to find the riser you need, and it comes out at roughly the C-value plus the tread depth multiplied by R/D, the slope of your line of sight down to the touchline. In the front row you are close to the pitch and only just above it, so you look across it and a small step will do. Twenty rows back you are higher, so you look down more steeply, R/D is bigger and each riser has to be taller. Taller risers lift the next row higher still, so the effect compounds.

That is why a well-designed stand curves upwards like a ski jump rather than rising in a straight line. Upper tiers start high and far back, so they begin steep and get steeper. Eventually they run into the rake limit, covered in our guide to how steep stadium stands can be.

3D view of Harbour Park, a Stadium Designer preset ground
Harbour Park: every stand was built to a target C-value, so the rake follows from the sightlines. The two-tier North Stand rises from 22° at the front to 35° at the back.

How Stadium Designer sets each riser

In the game you never type in a rake. You choose rows, tiers and a target C-value for each tier, and the engine works out every riser the way a stadium architect would:

  1. Each row is 800 mm deep and each seat 500 mm wide. A seated spectator's eye is 1.15 m above the tread.
  2. For each row, the engine measures the distance and height to the near touchline and solves the formula for the riser that hits your target C.
  3. If that riser would be steeper than 35°, it is capped at 560 mm and the row gets whatever C-value that leaves.
  4. The worst C-value anywhere in the ground goes on the status bar: green at 90 mm or more, amber below that, red below 60 mm.

Here is how that plays out on Harbour Park:

The deep two-tier stands finish steepest, because their upper tiers start high above the pitch. The single-tier stands never need to go as steep. The Kiln shows the other side of the trade-off: its Furnace stand has 34 rows in a single tier, reaches 35° and still only manages a C-value of 72 mm at worst.

In Stadium Designer

Open the editor, select a stand and change its C target. The derived rake and the achieved C update as you type: raise the target and the back rows climb; lower it and the stand flattens and gets shorter, which saves money but costs view. Adding rows to a single tier eventually hits the rake cap, and the fix is usually a second tier set back and above the first.

The Tournament host challenge asks for 60,000+ seats, C ≥ 90 on every tier and 5% hospitality, score ≥ 85, which is harder than it sounds on a bowl of 60,000 seats. If you prefer something smaller and louder, try The Cauldron.

Try it

Open Harbour Park in the editor, or take the Tournament host challenge: A showpiece for the opening match of a summer tournament.

Frequently asked questions

What is a C-value in a stadium?

The C-value is the height, in millimetres, by which a spectator's line of sight to the pitch clears the eyes of the person in the row in front. The bigger it is, the more easily you see over the heads in front. It depends on the riser height, the row depth, and how far and how high you sit from the point you are looking at.

What is a good C-value?

UK guidance from the Sports Grounds Safety Authority recommends 90 to 120 mm for new seating, and asks designers to show that viewing is not compromised if they go below 90 mm. 120 mm is usually treated as the ideal and 60 mm as the absolute minimum. Stadium Designer passes a stand at 90 mm or more and flags anything under 60 mm as an error.

Why are the back rows of a stand steeper than the front rows?

The higher and further back you sit, the more steeply you look down at the touchline, so each row has to rise further above the one in front to keep the same clearance. A stand designed to a constant C-value curves upwards from front to back rather than rising in a straight line.

What happens when a stand hits the rake limit?

Rows cannot get any steeper, so the C-value falls in the back rows instead. In Stadium Designer every riser is capped at 35 degrees (560 mm on a 800 mm row). At The Kiln, the Furnace reaches that cap and its worst C-value drops to 72 mm.

Do sightlines matter for safe standing areas?

Yes. The SGSA's safe standing guidance asks for C-values of 90 to 120 mm in seated areas designed for standing, including for wheelchair users. For standing spectators the C-value only needs to be checked for every second tread, because people on their feet shift position more.

Sources

  1. Guide to Safety at Sports Grounds (the Green Guide) (Sports Grounds Safety Authority, sixth edition)
  2. Supplementary Guidance 01: Safe standing in seated areas (PDF) (SGSA, second edition, July 2022: 90–120 mm C-values, every-second-tread rule)
  3. Sightline (architecture) (Wikipedia: C-value definition and the 60/90/120 mm FIFA standards)
  4. C-value (Designing Buildings Wiki: definition)

Rules of thumb for a design game, not engineering or safety advice. Stadium Designer's numbers come from a simplified model; real grounds are designed by qualified engineers to the Guide to Safety at Sports Grounds and local licensing conditions.